Littelfuse 0215010.MXF11P Ceramic Fuse 10A 250VAC Equivalent & Substitute Parts

Part Overview

The Littelfuse 0215010.MXF11P is a 10 A 250 V AC DC ceramic cartridge fuse with radial bend cylinder packaging for through-hole mounting applications. This component is classified as Active product status and is ROHS3 compliant. Equivalent and substitute parts are identified when component availability is limited, supply chain disruptions occur, or design flexibility permits selection from qualified alternatives within the same electrical and mechanical parameter set.

Substiute Parts

0215010.MXF11P

Littelfuse Inc.In Stock: 63860215010.MXF11P Datasheet

Current PartRFQ

0215010.MXF20P

Littelfuse Inc.In Stock: 20790215010.MXF20P Datasheet

Parametric EquivalentRFQ

0215010.MXF34P

Littelfuse Inc.In Stock: 16190215010.MXF34P Datasheet

Parametric EquivalentRFQ

0215010.MXF56P

Littelfuse Inc.In Stock: 23630215010.MXF56P Datasheet

Parametric EquivalentRFQ

0001.2514

SCHURTER Inc.In Stock: 230450001.2514 Datasheet

DirectRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitute parts are grouped into two categories based on electrical and mechanical compatibility:

Parametric Equivalents (Littelfuse Series 215): Parts 0215010.MXF20P, 0215010.MXF34P, and 0215010.MXF56P are parametric equivalents sharing identical electrical specifications (10 A, 250 V AC, slow blow response, 1.5kA breaking capacity) and mechanical form factor (radial bend cylinder, 5.20mm x 20.00mm). These parts differ only in internal construction variants and approval agency certifications. All three are Active status products suitable for direct substitution in through-hole applications.

Direct Manufacturer Alternative (SCHURTER 0001.2514): This part shares the core electrical parameters (10 A, 250 V AC, slow blow response, 5.20mm x 20.00mm ceramic cartridge) but differs in mounting requirement (requires holder versus radial bend) and DC voltage rating (150 V DC). This part is included as a functional alternative when holder-based mounting is acceptable in the circuit design.

Parameter Comparison

Engineering Selection Recommendations

Primary Substitutes (0215010.MXF20P, 0215010.MXF34P, 0215010.MXF56P): These Littelfuse Series 215 parts are direct parametric equivalents with identical electrical and mechanical specifications. All three maintain Active product status and ROHS3 compliance. Selection among these three is determined by approval agency requirements specific to the end application. The 0215010.MXF20P includes BSI and METI certifications; 0215010.MXF34P includes BSI and METI certifications; 0215010.MXF56P includes CQC and UR certifications. Choose based on regional compliance and certification requirements.

Alternative Substitute (0001.2514 SCHURTER): This part is suitable only when the circuit design accommodates holder-based mounting instead of radial bend through-hole mounting. The SCHURTER part provides higher inventory availability (22,984 pcs) and includes explicit DC voltage rating (150 V DC). Use this part only if mechanical mounting flexibility exists and DC voltage requirements do not exceed 150 V.

Frequently Asked Questions (FAQ)

Q: Can 0215010.MXF20P, 0215010.MXF34P, and 0215010.MXF56P be used interchangeably with 0215010.MXF11P?

A: Yes. These three parts are parametric equivalents with identical current rating (10 A), voltage rating (250 V AC), response time (slow blow), breaking capacity (1.5kA), and mechanical form factor (radial bend cylinder, 5.20mm x 20.00mm). Selection is based on approval agency certifications required for the specific application region.

Q: What is the difference between radial bend cylinder and 5mm x 20mm packaging?

A: Radial bend cylinder is a through-hole mounting configuration where leads are pre-formed for direct PCB insertion. The 5mm x 20mm designation refers to the cartridge dimensions but requires a separate holder component for mounting. The 0001.2514 SCHURTER part uses the holder-based approach.

Q: Can the SCHURTER 0001.2514 replace the Littelfuse 0215010.MXF11P directly?

A: Direct replacement is not possible without circuit modification. The SCHURTER part requires a fuse holder, whereas the Littelfuse part has integrated radial leads for through-hole mounting. Use the SCHURTER part only if the PCB design can accommodate a fuse holder assembly.

Q: Are all substitute parts ROHS3 compliant?

A: Yes. All parts listed (0215010.MXF11P, 0215010.MXF20P, 0215010.MXF34P, 0215010.MXF56P, and 0001.2514) are ROHS3 compliant and REACH unaffected.

Q: What approval agencies are common to all substitute parts?

A: CE and VDE certifications are present across all parts. Additional certifications vary by manufacturer and part variant. Consult the approval agency list for each part number to confirm compliance with regional requirements.