ELVF08400 Terminal Block Plug - Equivalent & Substitute Parts

Part Overview

The ELVF08400 is an 8-position terminal block plug manufactured by Amphenol PCD, designed for free-hanging in-line applications with 0.150" (3.81mm) pitch spacing. This component features female sockets with screw-rising cage clamp termination, rated for 12 A at 300 V (UL). The product is active and in stock with 717 units available. Alternative models are identified to support supply chain flexibility, design revisions, or inventory optimization while maintaining electrical and mechanical compatibility within specified parameter ranges.

Substiute Parts

ELVF08400

Amphenol PCDIn Stock: 768ELVF08400 Datasheet

Current PartRFQ

1850725

Phoenix ContactIn Stock: 11751850725 Datasheet

SimilarRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitution eligibility for the ELVF08400 is determined by the following critical parameters:

• Electrical Compatibility: Current and voltage ratings must meet or exceed UL specifications (12 A at 300 V minimum)
• Mechanical Compatibility: 8-position configuration with 0.150" (3.81mm) pitch spacing and 180° free-hanging in-line orientation
• Termination Interface: Screw-based termination systems (rising cage clamp or pressure clip variants) compatible with 16-28 AWG wire gauge
• Regulatory Compliance: UL94 V-0 flammability rating and RoHS compliance required
• Environmental Ratings: Operating temperature and moisture sensitivity level (MSL 1) specifications

The substitute part 1850725 (Phoenix Contact COMBICON FRONT-MC series) meets these core substitution criteria while maintaining functional equivalence for the specified application.

Parameter Comparison

Engineering Selection Recommendations

ELVF08400 (Amphenol PCD) is the primary specification. This component is active, RoHS compliant, and rated for 12 A at 300 V (UL). It is suitable for applications requiring the specified current capacity and mechanical form factor.

1850725 (Phoenix Contact) serves as a functional substitute where the following conditions are met:

• Application current requirement does not exceed 8 A (UL rating of substitute)
• Voltage requirement is 300 V or lower (UL rating of substitute)
• Screw-pressure clip termination is acceptable in place of rising cage clamp
• Reduced insulation height (0.484" vs. 0.850") is compatible with board layout and connector housing
• ROHS3 compliance satisfies regulatory requirements equivalent to RoHS Compliant status

Both parts maintain UL94 V-0 flammability rating, MSL 1 moisture sensitivity, and 0.150" (3.81mm) pitch spacing. Selection between these parts depends on current capacity requirements and termination mechanism preference for the specific application.

Frequently Asked Questions (FAQ)

Q: Can 1850725 replace ELVF08400 in all applications?

A: No. The 1850725 is rated for 8 A (UL), while the ELVF08400 is rated for 12 A (UL). Substitution is valid only when the application current requirement does not exceed 8 A at 300 V.

Q: What is the difference between rising cage clamp and pressure clip termination?

A: Both are screw-based termination methods. Rising cage clamp (ELVF08400) and pressure clip (1850725) differ in mechanical clamping mechanism. Both are suitable for 16-28 AWG wire gauge range, though 1850725 extends to 30 AWG.

Q: Are there packaging differences between these parts?

A: Yes. ELVF08400 is supplied in Tray packaging (717 units in stock), while 1850725 is supplied in Bulk packaging (1092 units in stock). Packaging does not affect electrical or mechanical compatibility.

Q: Do both parts meet the same compliance standards?

A: Both parts are UL94 V-0 rated and have MSL 1 moisture sensitivity. ELVF08400 is RoHS Compliant; 1850725 is ROHS3 Compliant. ROHS3 represents an updated compliance standard and is functionally equivalent for component selection purposes.

Q: What is the significance of insulation height difference?

A: ELVF08400 has 0.850" (21.59mm) insulation height; 1850725 has 0.484" (12.30mm). This difference affects physical clearance in connector housings and PCB layouts. Verify mechanical fit before substitution.

Q: Can wire gauge range differences affect substitution?

A: ELVF08400 accepts 16-28 AWG; 1850725 accepts 16-30 AWG. The 1850725 supports finer wire gauges (29-30 AWG). For applications using 16-28 AWG, both parts are compatible. Applications requiring 29-30 AWG wire must use 1850725.