ACML-0201-600-T Ferrite Bead 60 Ohm 0201 Equivalent & Substitute Parts

Part Overview

The ACML-0201-600-T is a single-line ferrite bead manufactured by Abracon LLC, rated at 60 Ohms impedance at 100 MHz in a 0201 (0603 Metric) surface mount package. This component is designed for electromagnetic interference (EMI) suppression in signal and power line applications. The part is Active status and ROHS3 compliant. Substitute parts may be required due to supply chain availability, lead time constraints, or specific packaging preferences while maintaining equivalent electrical and mechanical performance.

Key Parameters

Parameter	Value
Impedance @ 100 MHz	60 Ohms
Current Rating (Max)	200 mA
DC Resistance (Max)	400 mOhm
Package / Case	0201 (0603 Metric)
Number of Lines	1
Operating Temperature Range	-55°C to 125°C
Mounting Type	Surface Mount
RoHS Status	ROHS3 Compliant
Moisture Sensitivity Level	1 (Unlimited)

Substitute Part Grouping Explanation

Ferrite bead substitution is determined by the following critical parameters: impedance value at 100 MHz, current rating capacity, DC resistance, package dimensions, and compliance certifications. Parts are grouped into two categories based on electrical equivalence:

Category 1: Direct Electrical Equivalents (60 Ohms @ 100 MHz, 200 mA) These parts match the ACML-0201-600-T impedance and current rating exactly, with identical or lower DC resistance. They provide direct functional replacement without circuit redesign.

Category 2: Compatible Alternatives (50-70 Ohms @ 100 MHz, 300 mA) These parts operate within acceptable impedance tolerance ranges and offer higher current capacity. They are suitable for applications where the circuit design permits impedance variation within ±17% and where increased current headroom is beneficial.

All substitute parts maintain the 0201 (0603 Metric) package footprint, surface mount configuration, -55°C to 125°C operating temperature range, and MSL 1 rating.

Parameter Comparison

Manufacturer Part Number	Manufacturer	Impedance @ 100 MHz	Current Rating (Max)	DC Resistance (Max)	Package	Height (Max)	Packaging Type	RoHS Status
ACML-0201-600-T	Abracon LLC	60 Ohms	200 mA	400 mOhm	0201 (0603 Metric)	0.014" (0.35 mm)	Bulk	ROHS3
742692002	Würth Elektronik	60 Ohms	300 mA	350 mOhm	0201 (0603 Metric)	0.013" (0.33 mm)	Tape & Reel	ROHS3
BLM03AG700SN1D	Murata Electronics	70 Ohms	200 mA	400 mOhm	0201 (0603 Metric)	0.013" (0.33 mm)	Cut Tape & Digi-Reel	ROHS3
BMC1HY0050AN	TE Connectivity Passive Product	50 Ohms	300 mA	300 mOhm	0201 (0603 Metric)	0.013" (0.33 mm)	Cut Tape	ROHS3
BMC1HY0060AN	TE Connectivity Passive Product	60 Ohms	300 mA	350 mOhm	0201 (0603 Metric)	0.013" (0.33 mm)	Cut Tape	ROHS3
BMC1HY0070AN	TE Connectivity Passive Product	70 Ohms	300 mA	350 mOhm	0201 (0603 Metric)	0.013" (0.33 mm)	Cut Tape	ROHS3
FB060303T-500Y-S	Cal-Chip Electronics, Inc.	50 Ohms	300 mA	300 mOhm	0201 (0603 Metric)	0.013" (0.33 mm)	Tape & Reel	RoHS
FB060303T-600Y-S	Cal-Chip Electronics, Inc.	60 Ohms	300 mA	350 mOhm	0201 (0603 Metric)	0.013" (0.33 mm)	Tape & Reel	RoHS
FB060303T-700Y-S	Cal-Chip Electronics, Inc.	70 Ohms	300 mA	350 mOhm	0201 (0603 Metric)	0.013" (0.33 mm)	Tape & Reel	RoHS
GZ0603D600TF	Shenzhen Sunlord Electronics Co., Ltd.	60 Ohms	200 mA	400 mOhm	0201 (0603 Metric)	0.014" (0.35 mm)	Tape & Reel	ROHS3

Engineering Selection Recommendations

Direct Replacement (Highest Compatibility): 742692002 (Würth Elektronik), BMC1HY0060AN (TE Connectivity), FB060303T-600Y-S (Cal-Chip), and GZ0603D600TF (Sunlord) all provide 60 Ohms impedance matching the ACML-0201-600-T. The Würth, TE, and Cal-Chip variants offer increased current capacity (300 mA vs. 200 mA) with lower or equal DC resistance, providing enhanced performance margin. All are ROHS3 compliant or RoHS compliant.

Alternative Impedance Options: BLM03AG700SN1D (Murata), BMC1HY0070AN (TE Connectivity), and FB060303T-700Y-S (Cal-Chip) provide 70 Ohms impedance with 300 mA current capacity. BMC1HY0050AN (TE Connectivity) and FB060303T-500Y-S (Cal-Chip) provide 50 Ohms impedance with 300 mA current capacity. These alternatives are suitable for circuits where impedance tolerance of ±17% is acceptable and where the application benefits from higher current ratings.

All substitute parts maintain identical package footprint, operating temperature range, and moisture sensitivity classification. Selection should prioritize parts matching the original 60 Ohms specification unless circuit design documentation explicitly permits impedance variation.

Frequently Asked Questions (FAQ)

Q: Can I substitute a 70 Ohm ferrite bead for the 60 Ohm ACML-0201-600-T? A: Yes, if your circuit design permits impedance tolerance. The 70 Ohm variants (BLM03AG700SN1D, BMC1HY0070AN, FB060303T-700Y-S) provide approximately 17% higher impedance. This is acceptable in applications where EMI suppression curves are broad or where the design margin accommodates this variation. Verify with your circuit schematic or EMI analysis documentation.

Q: What is the difference between Tape & Reel and Cut Tape packaging? A: Both are surface mount compatible formats. Tape & Reel packaging (742692002, FB series, GZ0603D600TF) is supplied on continuous reels for automated assembly lines. Cut Tape packaging (BMC series) is supplied in shorter tape segments. Both formats contain identical components; packaging choice depends on your assembly process and volume requirements.

Q: Are all substitute parts ROHS3 compliant? A: Most substitute parts are ROHS3 compliant (742692002, BLM03AG700SN1D, BMC series, GZ0603D600TF). Cal-Chip Electronics FB series parts are RoHS compliant. Both certifications meet environmental and hazardous substance restrictions. Verify your specific compliance requirements with your procurement or quality department.

Q: Can I use a 300 mA rated ferrite bead in place of the 200 mA ACML-0201-600-T? A: Yes. Higher current ratings provide additional safety margin and are directly compatible. Parts like 742692002, BMC1HY0060AN, and FB060303T-600Y-S are rated for 300 mA and can replace the 200 mA original without circuit modification. This substitution improves thermal performance and component reliability.

Q: What is DC Resistance (DCR) and why does it matter? A: DC Resistance is the resistive loss of the ferrite bead at direct current. Lower DCR reduces power dissipation and heat generation. The ACML-0201-600-T has 400 mOhm DCR. Substitutes with 350 mOhm (742692002, BMC1HY0060AN, FB060303T-600Y-S) or 300 mOhm (BMC1HY0050AN, FB060303T-500Y-S) provide improved efficiency. Higher DCR values are acceptable if thermal analysis confirms acceptable operating conditions.

Q: Are the physical dimensions identical across all substitute parts? A: Package footprint is identical (0201 / 0603 Metric, 0.024" L × 0.012" W). Height varies slightly: ACML-0201-600-T and GZ0603D600TF are 0.014" (0.35 mm), while most substitutes are 0.013" (0.33 mm). This 0.001" difference is negligible for PCB assembly and does not affect component placement or soldering.

Request Quote (Ships tomorrow)

Part Number

Quantity

Company

Contact Name

E-mail

Message