8PCV-06-007 Equivalent & Substitute Parts

Part Overview

The 8PCV-06-007 is a 6-circuit barrier block connector manufactured by TE Connectivity AMP Connectors. This terminal block features 0.438" (11.12mm) pitch spacing with screw-based top termination and PC pin bottom termination, designed for through-hole mounting applications. The part is currently active in production with 930 units in stock. Substitute parts are identified when equivalent barrier block connectors share the same physical form factor and core electrical characteristics, enabling direct replacement in applications where the specified performance envelope is maintained.

Substiute Parts

8PCV-06-007

TE Connectivity AMP ConnectorsIn Stock: 10278PCV-06-007 Datasheet

Current PartRFQ

0387306306

MolexIn Stock: 14610387306306 Datasheet

SimilarRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitution eligibility for the 8PCV-06-007 is determined by the following critical parameters:

Physical Compatibility Parameters:

• Number of circuits: 6
• Pitch spacing: 0.438" (11.12mm)
• Mounting type: Through hole
• Bottom termination: PC pin
• Top termination: Screws

Electrical Performance Parameters:

• Current rating: 30A minimum
• Voltage rating: 600V minimum
• Wire gauge accommodation: 10-18 AWG minimum

Environmental & Compliance Parameters:

• Operating temperature range: -40°C ~ 120°C minimum
• RoHS compliance status
• Flammability rating: UL94 V-0

The identified substitute part (Molex 0387306306) shares identical physical form factor characteristics (6 circuits, 0.438" pitch, through-hole mounting, PC pin termination, screw top termination). However, this substitute exhibits reduced electrical performance specifications (15A current rating vs. 30A; 300V voltage rating vs. 600V) and a narrower operating temperature range (-40°C ~ 100°C vs. -40°C ~ 120°C). These differences establish the substitution as a downgrade scenario, applicable only when the application requirements do not exceed the substitute part's electrical and thermal limits.

Parameter Comparison

Engineering Selection Recommendations

Primary Part Selection (8PCV-06-007): The 8PCV-06-007 is the specified component and remains the preferred selection for applications requiring the full performance envelope: 30A current capacity, 600V voltage rating, and extended operating temperature range to 120°C. This part carries active product status with RoHS compliance and UL94 V-0 flammability certification, supporting high-reliability applications.

Substitute Part Selection (0387306306): The Molex 0387306306 serves as a substitute only for applications where electrical and thermal requirements are reduced. This part is suitable when:

• Maximum current demand does not exceed 15A
• Maximum voltage does not exceed 300V
• Operating temperature remains within -40°C to 100°C
• Wire gauge requirements fall within 14-22 AWG range

Both parts maintain RoHS compliance and MSL Level 1 status. The Molex substitute features a 2-wall barrier design compared to the 3-wall design of the primary part, and does not carry a specified UL94 flammability rating. The substitute part carries ROHS3 compliance designation.

Frequently Asked Questions (FAQ)

Q: Can the Molex 0387306306 be used as a direct replacement for the 8PCV-06-007?

A: Direct replacement is possible only when the application electrical requirements do not exceed the substitute part's specifications. The Molex part is rated for 15A maximum current and 300V maximum voltage, compared to the TE Connectivity part's 30A and 600V ratings. If the application requires either the higher current capacity or voltage rating, the Molex substitute is not compatible.

Q: What is the difference between the 3-wall and 2-wall barrier designs?

A: The 8PCV-06-007 features a 3-wall (tri) barrier configuration, while the Molex 0387306306 features a 2-wall (dual) barrier configuration. This structural difference affects electrical isolation between circuits. The 3-wall design provides enhanced separation.

Q: Are both parts suitable for the same wire gauge range?

A: No. The 8PCV-06-007 accommodates 10-18 AWG wire, while the Molex 0387306306 accommodates 14-22 AWG wire. The TE Connectivity part supports larger gauge conductors (10 AWG), while the Molex part supports smaller gauge conductors (22 AWG). Wire gauge compatibility must be verified for the specific application.

Q: What is the operating temperature difference between these parts?

A: The 8PCV-06-007 operates from -40°C to 120°C, while the Molex 0387306306 operates from -40°C to 100°C. Applications requiring operation above 100°C require the TE Connectivity part.

Q: Do both parts have the same flammability rating?

A: The 8PCV-06-007 carries a UL94 V-0 flammability rating. The Molex 0387306306 does not have a specified flammability rating in the provided data. Applications requiring UL94 V-0 certification must use the TE Connectivity part.

Q: Are both parts RoHS compliant?

A: Yes. The 8PCV-06-007 is RoHS Compliant, and the Molex 0387306306 is ROHS3 Compliant. Both meet RoHS requirements.

Q: What is the pitch spacing, and is it identical between both parts?

A: Both parts feature 0.438" (11.12mm) pitch spacing. This identical spacing ensures physical compatibility for PCB mounting and circuit board layout purposes.

Q: Can the wire gauge difference affect substitution decisions?

A: Yes. The 8PCV-06-007 accepts 10-18 AWG wire, while the Molex 0387306306 accepts 14-22 AWG wire. If the application uses 10 AWG or 12 AWG conductors, the Molex part cannot accommodate these larger gauges. Conversely, if the application uses 20 AWG or 22 AWG conductors, the TE Connectivity part can accommodate these, but the Molex part is also suitable.

Q: What is the current rating difference, and why does it matter?

A: The 8PCV-06-007 is rated for 30A continuous current, while the Molex 0387306306 is rated for 15A continuous current. This 2:1 difference is critical for high-current applications. Exceeding the 15A rating of the Molex part creates thermal and safety risks.